ENCAD T-200 Service Manual Page 1

SERVICE MANUAL

xENCAD T-200 and T-200+ Service ManualChapter 4 Troubleshooting... 4-1Introduction ...

Troubleshooting 4-15ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Line Quality • drive

Troubleshooting 4-16CadJet T-200 Service ManualInitialization TroubleshootingThe sequence that the printer follows during initialization (power up) is

Troubleshooting 4-17CadJet T-200 Service ManualTurn the unit off immediately after the LED D5 returns to thedimly lit status to ensure no damage occur

55-1IntroductionChapter 5 contains the procedures for removal and replacement of theT-200 and T-200+ printer assemblies and mechanisms. Illustrations

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-2Always turn the printer OFF, remove the power cordand the interface cable before beginnin

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-34. Using a #2 Phillips screwdriver, loosen the top and front captivefastener screws and r

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-4Removing the MPWA ConnectorsCAUTIONDo not pull the cables from the connectors on the J3lo

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-51. Disconnect the Display Cable connector at the J3 location. Pullforward on the connect

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-6To remove the MPWA:1. Put on an ESD wrist strap.2. Use a #2 6” Phillips screwdriver to re

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-74. While holding the Right Side Plate, remove the screws securingthe side plate to the Pl

xiENCAD T-200 and T-200+ Service ManualMemory Module Removal ...

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-84. Reinstall the Trailing Cable at J6.When inserting the Trailing Cable connector, apply

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-9Memory Module InstallationThe memory module is secured by locking tabs located at both of

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-10Figure 5-4. Removal of the Left Cover.Reinstalling the Left CoverTo reinstall the Left C

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-114. Remove the Right Cover, MPWA and Right Side Plate for removalof the Servo Motor.SERVO

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-12PUSH IN HERETO SLACKENCARRIAGE BELTFigure 5-6. Compression of Frame Tensioner.8. Support

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-137. Move the Carriage Assembly back and forth to check the CarriageBelt tension.8. Reinst

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-14Reinstalling the Display AssemblyReinstall Display Assembly by reversing the procedure u

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-153. Reach into the Right Cover and pull back on the Service Stationrelease tab located on

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-16Remove the Carriage Assembly, Carriage Belt andthe Frame Tensioner1. Remove the Top Cove

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-173. With a flathead screwdriver, press the Electronics Cover tab locatedin the upper slot

xiiENCAD T-200 and T-200+ Service ManualList of IllustrationsFigure PageChapter 1 General Description1-1. T-200 and T-200+ Inkjet Printer/Plotter ...

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-188. Push the Carriage Belt through the Frame Tensioner enough toremove the Idler Pulley A

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-19CARRIAGE BELTBELT CLAMPRIGHT POST OFBELT CLAMPLEFT POST OFBUMPFigure 5-12. Carriage Bel

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-20Remove the Carriage PWACAUTIONIntegrated circuits may become weakened or damaged byelect

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-214. Unlock the latch on the right end of the Carriage Assembly and liftup the right end o

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-22THIS PIECE OF PLASTIC(ONE ON EACH SIDE) MUSTCLEAR THE RIDGES ON THEUNDERSIDE OF THE HOLD

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-233. To remove the Encoder Sensor:a. Unlock the connector at J2 and remove the flex cable.

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-24c. Grasp the Paper Sensor between thumb and index finger andguide the sides of the board

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-25CARRIAGEBUSHINGLATCHFigure 5-16. Carriage Bushing Removal.2. Use a flat tip screwdriver

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-26TABSFigure 5-17. Carriage Bushing Installation.5. Orient the new Bushing as shown in Fi

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-275. Slide the Carriage Assembly onto the left end of the Slide Shaft,making sure that the

xiiiENCAD T-200 and T-200+ Service ManualList of Illustrations (cont)Figure PageChapter 3 Maintenance (cont)3-16. Test Cartridge Installed ...

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-2815. Fit the Compression Spring over the post at the back of the Y-ArmAssembly.16. Fit th

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-29Reinstalling the Trailing Cable1. Apply two new pieces of double sided tape to the Stabi

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-30Removing the Power Supply and ON/OFF SwitchNOTETo gain access to all the screws that sec

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-31REMOVELOOSENFigure 5-18. Revealing the Power Supply Screws.

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-32Reinstalling the Power Supply and ON/OFF SwitchPOWER SUPPLYCABLEFAN ASSEMBLYEXHAUSTSUPPO

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-332. Connect the Power Cable coming from the MPWA to theconnector on the Power Supply. Ma

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-34Figure 5-20. Stabilizer Bracket Removal.5. Use a 7/64 Hex Nut Driver to remove the thre

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-35in the Y-Arm and use the 7/64 Hex Nut Driver to tighten them.(The exact positioning of t

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-36RIGHTROLLGUIDERIGHTSIDE PLATESCREWS(4)SCREWS(4)LEFTCOVERLEFTROLLGUIDECAUTIONDO NOT REMOV

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-37Removing the Inner Platen PartsRefer to Figure 5-20 and Figure 5-22 during this procedur

xivENCAD T-200 and T-200+ Service ManualList of Illustrations (cont)Figure PageChapter 5 Assembly/Disassembly (cont)5-7. Removal of Display Assembly

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-386. Using a #1 6” or 8” Phillips screwdriver, remove the 4 black flat-head screws which h

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-399. Using a #1 6” or 8” Phillips screwdriver, loosen but do notremove the 2 black flat-he

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-40BOWED WASHERWASHERRETAINING RINGRETAINING RINGRETAINERSPRINGSCREWOILITEBUSHINGPIVOT NUTP

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-415. If you are replacing the Stepper Motor Bracket, you will need toremove the Retaining

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-423. Lay the Stepper Motor Assembly on the palm of your right handand use your fingertips

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-4311. Hold the Fan in place with your left hand and insert the screws.Make sure that the s

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-4411. Route the Display Cable through the top left edge in the Right SidePlate. Bring the

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-455. Using your fingers, pull the Upper Pinch Roller Support forward.Thie will seperate it

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-46Installing the Upper Roller SupportsMake sure that the Carriage Belt is kept looped over

ENCAD T-200 and T-200+ Service ManualAssembly\Disassembly 5-47NOTEMake sure that the Carriage Belt is not twisted. One wayto check this is by standin

xvENCAD T-200 and T-200+ Service ManualList of TablesTable PageChapter 1 General DescriptionChapter 2 Theory of OperationChapter 3 Maintenance3-1.

66-1Parts ListThis chapter lists the items and their associated numbers for the partsand assemblies of the ENCAD T-200 and T200+ printers that are fie

ENCAD T-200 and T200+ Service ManualParts List 6-26-1 1 ROLLGUIDE, RIGHT, ASSY ... 206828-56-1 2 ROLLGUIDE, LEFT, ASSY ...

ENCAD T-200 and T200+ Service ManualParts List 6-3Figure 6-1. Left Side Parts Breakdown.

ENCAD T-200 and T200+ Service ManualParts List 6-4FIGURE ITEM PART NAME PART #6-2 1 SPRING, COMPESSION ... 2090526-2 2 RETRACTIN

ENCAD T-200 and T200+ Service ManualParts List 6-5Figure 6-2. Platen and Above Parts Breakdown.

ENCAD T-200 and T200+ Service ManualParts List 6-6FIGURE ITEM PART NAME PART #6-3 1 PRINT SERVER (OPTIONAL) ... 218239-006-3 2 SIDE PLATE

ENCAD T-200 and T200+ Service ManualParts List 6-7Figure 6-3. Right Side Parts Breakdown.

ENCAD T-200 and T200+ Service ManualParts List 6-8FIGURE ITEM PART NAME PART #6-4 1 MOTOR ASSY, SERVO,W/FERRITE ...

ENCAD T-200 and T200+ Service ManualParts List 6-9Figure 6-4. Inner Platen Parts Breakdown.

ENCAD T-200 and T200+ Service ManualParts List 6-10FIGURE ITEM PART NAME PART #6-5 1 COVER, CARRIER ELECTRONICS ... 215111-026-5 2 CARRIAGE PWA .

11-1General DescriptionFigure 1-1. T-200 and T-200+ Inkjet Printer/Plotter.IntroductionThis manual provides service information for the ENCAD®, Inc.

ENCAD T-200 and T200+ Service ManualParts List 6-11Figure 6-5. Carriage Assembly Parts Breakdown.

ENCAD T-200 and T200+ Service ManualParts List 6-12FIGURE ITEM PART NAME PART #6-6 1 SEAL, 104/208 ... 2065026-

ENCAD T-200 and T200+ Service ManualParts List 6-13Figure 6-6. Service Station Assembly Parts Breakdown.

General Description 1-2ENCAD T-200 and T-200+Service Manualmedia uses different maximum plotting areas than roll media. See thePrinter Specifications

General Description 1-3ENCAD T-200 and T-200+Service ManualOverviewPrinters draw according to instructions issued from a “host” computer.Every printer

General Description 1-4ENCAD T-200 and T-200+Service ManualWarnings, Cautions and NotesWarnings, cautions and notes are used when additional informati

T-200ANDT-200+COLOR INKJETPRINTER/PLOTTERSSERVICE MANUALPart Number 219863-00®

General Description 1-5ENCAD T-200 and T-200+Service ManualPrinter SpecificationsThe specifications and performance characteristics of the T-200and T-

General Description 1-6ENCAD T-200 and T-200+Service ManualContents of this Service ManualFigures are used in this manual to clarify procedures. They

General Description 1-7ENCAD T-200 and T-200+Service ManualChapter 3 MAINTENANCE - This chapter covers thescheduled maintenance, cleaning procedures

General Description 1-8ENCAD T-200 and T-200+Service ManualTechnical SupportENCAD offers full technical support and service for its various prod-ucts.

22-1IntroductionThis chapter explains the mechanical and electrical theory of operationof the ENCAD T-200 and T-200+ color inkjet printers.The T-200/T

Theory of Operation 2-2ENCAD T-200 and T-200+ Service ManualCARRIAGE AXIS DRIVEELECTRICAL CONNECTIONMECHANICAL CONNECTIONMAIN DATA BUSMPWADISPLAYCIRCU

Theory of Operation 2-3ENCAD T-200 and T-200+ Service ManualPaper (Media) Axis DriveLOWER ROLLER SHAFT ASSYPINCH ROLLERSSTEPPER MOTORREDUCTION GEARFig

Theory of Operation 2-4ENCAD T-200 and T-200+ Service ManualThe Carriage Axis DriveFigure 2-3. Carriage Axis Drive.The Carriage Axis Drive moves the

Theory of Operation 2-5ENCAD T-200 and T-200+ Service ManualMain Printed Wiring Assembly (MPWA)SERIALEEPROMMICRO-PROCESSOR(CPU)OSCY1STEPPER MOTORCONTR

Theory of Operation 2-6ENCAD T-200 and T-200+ Service ManualMicroprocessorThe microprocessor (an IBM PowerPC) is the central processor unitwhich super

iiiENCAD T-200 and T-200+ Service ManualCopyright Eastman Kodak Company, 2002KODAK, ENCAD® and CadJet® are trademarks ofEastman Kodak Company.Other tr

Theory of Operation 2-7ENCAD T-200 and T-200+ Service ManualThe gate array contains the hardware logic for dot firing, monitoringchanges in the Carria

Theory of Operation 2-8ENCAD T-200 and T-200+ Service ManualThe system firmware is stored in Flash EEPROM. The FlashEEPROM allows the firmware to be

Theory of Operation 2-9ENCAD T-200 and T-200+ Service ManualStepper Motor ControllerFigure 2-6. Stepper Motor Controller.The media is driven by a Ste

Theory of Operation 2-10ENCAD T-200 and T-200+ Service Manual2. Motor current senseThe voltage across a series current sense resistor is measured andl

Theory of Operation 2-11ENCAD T-200 and T-200+ Service ManualServo Motor ControllerGATEARRAYMOTORDRIVERSERVOCONNECTORCARRIAGECONNECTORSERVOMOTORCARRIA

Theory of Operation 2-12ENCAD T-200 and T-200+ Service ManualFigure 2-8. Quadrature Signal Generation.The direction that the Carriage Assembly is mov

Theory of Operation 2-13ENCAD T-200 and T-200+ Service ManualControl PanelERRORREADYRESETSHORTCUT MENUMENUSELECTLOADFigure 2-9. Control Panel.The Con

Theory of Operation 2-14ENCAD T-200 and T-200+ Service ManualSELECT when depressed, accepts the slection shownon the displayUP ARROW cycles through th

Theory of Operation 2-15ENCAD T-200 and T-200+ Service ManualCarriage Assembly CircuitsCARTRIDGE 1CARTRIDGE 2CARTRIDGE 3CARTRIDGE 4OPTICAL ENCODEROPTI

Theory of Operation 2-16ENCAD T-200 and T-200+ Service ManualThe paper sensor circuitry senses for the presence of loaded media. Itdoes this automati

ivENCAD T-200 and T-200+ Service ManualFCC Statement (U.S.A.)The United States Federal Communications Commision has specified thatthe following notice

Theory of Operation 2-17ENCAD T-200 and T-200+ Service ManualPower SupplyAn internal UL recognized switching power module supplies power forthe printe

33-1MaintenanceIntroductionThis chapter contains general maintenance and cleaning instructionsfor the T-200 and T-200+ printer.Scheduled MaintenanceSc

ENCAD T-200 and T-200+ Service ManualMaintenance 3-2Cleaning ProceduresAlways turn the printer OFF, remove the power cord andthe interface cable befor

ENCAD T-200 and T-200+ Service ManualMaintenance 3-3Printer problems can be caused by an accumulation of dirt or othercontamination on the slide shaft

ENCAD T-200 and T-200+ Service ManualMaintenance 3-44. Using a cotton swab dampened with distilled water, wipe theseals and the rubber wiper in the se

ENCAD T-200 and T-200+ Service ManualMaintenance 3-5Figure 3-1. Encoder Strip Cleaning.Cartridge Dimples CleaningCARTRIDGEDIMPLEAREAFigure 3-2. Cart

ENCAD T-200 and T-200+ Service ManualMaintenance 3-6The cartridge dimple area can easily be contaminated by oils and dirt onfingers and hands or ink s

ENCAD T-200 and T-200+ Service ManualMaintenance 3-7Cleaning the flex cable contact area is very important due to the easeof which this area can becom

ENCAD T-200 and T-200+ Service ManualMaintenance 3-8Clean and Inspect Carriage AssemblyForeign material on the carriage assembly could short out signa

ENCAD T-200 and T-200+ Service ManualMaintenance 3-9Figure 3-4. Main PWA Connection Locations.Table 3-1. Main PWA Connections.J1 not used J7 Servo Mo

vENCAD T-200 and T-200+ Service ManualVDE StatementHiermit wird bescheinigt, daß der T-200/T-200+ in Übereinstimmung mitden Bestimmungen der BMPT-Amst

ENCAD T-200 and T-200+ Service ManualMaintenance 3-10Figure 3-5. Carriage PWA Connection Locations.Table 3-2. Carriage PWA Connections.J1 Yellow Driv

ENCAD T-200 and T-200+ Service ManualMaintenance 3-11LOCKINGMECHANISMCONNECTORASSEMBLYRIBBONUNLOCKEDLOCKEDFigure 3-6. Ribbon Connector Locking Mechan

ENCAD T-200 and T-200+ Service ManualMaintenance 3-12Servo Motor Winding Resistance CheckFigure 3-7. Servo Motor.1. Disconnect the servo motor connec

ENCAD T-200 and T-200+ Service ManualMaintenance 3-13Stepper Motor Winding Resistance CheckREDWIRE7.2-8.0ohms7.2-8.0ohmsFigure 3-8. Stepper Motor.1.

ENCAD T-200 and T-200+ Service ManualMaintenance 3-14Banding: Hardware vs SoftwareThe technician must be able to identify whether the banding that isb

ENCAD T-200 and T-200+ Service ManualMaintenance 3-152) Print a test file approved by ENCAD that uses only the printerdriver software and the ENCAD pr

ENCAD T-200 and T-200+ Service ManualMaintenance 3-166. Wiping during a print can sometimes cause a band of lighterdensity color in the image. Auto wi

ENCAD T-200 and T-200+ Service ManualMaintenance 3-1714. Static electricity. Using certain types of media (i.e. polyester-based media), static electri

ENCAD T-200 and T-200+ Service ManualMaintenance 3-18You will need the following:· Height Gauge Kit Assembly· 1/4" open and box end wrench (.110”

ENCAD T-200 and T-200+ Service ManualMaintenance 3-19MEASURESECONDMEASUREFIRSTMEASURELASTADJUST IFNECESSARYFigure 3-11. Measurement Positions for Sli

viENCAD T-200 and T-200+ Service ManualMaterial Safety Data SheetENCAD QIS (Quality Imaging Supplies) ink is nonhazardous, requiring nospecial disposa

ENCAD T-200 and T-200+ Service ManualMaintenance 3-20For example: If the Left = 0, Right = +0.004”, then the center shouldbe adjusted to + 0.002”. Th

ENCAD T-200 and T-200+ Service ManualMaintenance 3-21SPIN HEAD ONMICROMETER GAUGETO FACE BACKWARDSTIGHTEN SETSCREWSENSURE TIP EXTENDSBELOW CARTRIDGE1/

ENCAD T-200 and T-200+ Service ManualMaintenance 3-224. Remove the Cyan ink cartridge. Snap the test cartridge withthe micrometer gauge into the posi

ENCAD T-200 and T-200+ Service ManualMaintenance 3-23NOTEThe actual measurement is different than the true headheight due to the fact that the test ca

ENCAD T-200 and T-200+ Service ManualMaintenance 3-24Paper Skew AdjustmentThe purpose of the Paper Skew Adjustment is to make certain that thePinch Ro

ENCAD T-200 and T-200+ Service ManualMaintenance 3-25NOTEThe rollers should be adjusted moving from the rightside of the Platen to the left side of th

ENCAD T-200 and T-200+ Service ManualMaintenance 3-26ROLLERPINCH ROLLERASSEMBLYY-ARMLEFT MOUNTINGSCREWRIGHT MOUNTINGSCREWORIENTATIONSTANDING BEHIND TH

ENCAD T-200 and T-200+ Service ManualMaintenance 3-276. It is extremely important that you maintain downwardpressure (towards the floor) on the head o

ENCAD T-200 and T-200+ Service ManualMaintenance 3-28Other Functional RequirementsThe paper skew has a tendency to increase as the size of paper incre

ENCAD T-200 and T-200+ Service ManualMaintenance 3-29Adjustment of Pinch Roller SupportsNOTEBe sure to perform the adjustment according to the se-quen

viiENCAD T-200 and T-200+ Service ManualWARRANTY OR DAMAGE CLAIMSUnited StatesENCAD®, Inc., warrants its printers ("PRODUCT") to be free fro

ENCAD T-200 and T-200+ Service ManualMaintenance 3-30Observation of Paper Skew at Rear Media Alignment Mark1. Position a sheet of the appropriate size

ENCAD T-200 and T-200+ Service ManualMaintenance 3-31Observation of Paper Skew at Front Media Alignment Mark1. Press FEED MEDIA and then the UP ARROW

ENCAD T-200 and T-200+ Service ManualMaintenance 3-32Adjustment of the Mounting ScrewsFigure 3-24 shows how the motion (rapid drifting to the right or

ENCAD T-200 and T-200+ Service ManualMaintenance 3-33Color CalibrationThis procedure describes how to check that the cartridges are properlyaligned fo

ENCAD T-200 and T-200+ Service ManualMaintenance 3-34The “Color Horizontal Head-to-Head Calibration” checks the alignmentof the nozzles horizontally a

ENCAD T-200 and T-200+ Service ManualMaintenance 3-35Deadband AlignmentsDeadband calibration compensates for minute differences created whenbidirectio

ENCAD T-200 and T-200+ Service ManualMaintenance 3-36To perform the Slow Deadband AlignmentDepress the “Menu” key on the control panel to begin the ma

ENCAD T-200 and T-200+ Service ManualMaintenance 3-37To perform the Color Deadband AlignmentsDepress the “Menu” key on the control panel to begin the

ENCAD T-200 and T-200+ Service ManualMaintenance 3-38Paper Axis CalibrationThe paper axis calibration procedure ensures that the processing thatdrives

ENCAD T-200 and T-200+ Service ManualMaintenance 3-3933"Figure 3-27. Paper Axis Test.With a precision drafters measuring stick, measure the exac

viiiENCAD T-200 and T-200+ Service ManualTable of ContentsChapter 1 General Description ... 1

ENCAD T-200 and T-200+ Service ManualMaintenance 3-40Diagnostics MenuTo get to the Diagnostics Menu:Depress the “Menu” key on the control panel to beg

ENCAD T-200 and T-200+ Service ManualMaintenance 3-41Carriage Test - Prints 5 sets of 3 parallel lines to test the vibrationcharacteristics of the car

ENCAD T-200 and T-200+ Service ManualMaintenance 3-42Firmware Download/UpgradingThe normal method of downloading new firmware is to send the file as i

ENCAD T-200 and T-200+ Service ManualMaintenance 3-436. Wait approximately 20 to 40 seconds later until you hear aSINGLE beep, indicating the download

ENCAD T-200 and T-200+ Service ManualMaintenance 3-44Figure 3-28. MPWA Connections Diagram.LINENEUTGNDAC INPUT& PWR SWITCH123SWITCHINGPOWERSUPPLY

ENCAD T-200 and T-200+ Service ManualMaintenance 3-45Figure 3-29. Carriage PWA Connections Diagram.12345678910111213141516171819201234567891011121314

44-1TroubleshootingNo Power• printer not ON depress powerswitch• faulty power replace power cordcord• AC input not replace AC entrypresent at power mo

Troubleshooting 4-2ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).No Power (cont) • DC

Troubleshooting 4-3ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Media Does Not • medi

Troubleshooting 4-4ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Internal ERROR • dirt

ixENCAD T-200 and T-200+ Service ManualSlide Shaft Cleaning... 3-2Se

Troubleshooting 4-5ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Internal ERROR“Encode

Troubleshooting 4-6ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Internal ERROR“MPCB F

Troubleshooting 4-7ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Does Not Print• no me

Troubleshooting 4-8ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Ink Cartridge • flex

Troubleshooting 4-9ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Paper Skewing• steppe

Troubleshooting 4-10ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Printer Output is •

Troubleshooting 4-11ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Printer Output is •

Troubleshooting 4-12ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Printer Outputis Ban

Troubleshooting 4-13ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Noisy Operation• ink

Troubleshooting 4-14ENCAD T-200 and T-200+ Service ManualSymptoms Possible cause SolutionTable 4-1. Troubleshooting Table (cont).Line QualityDegraded